Home
Global Supplier Directory
APPLIANCE Engineer
Supplier Solutions
APPLIANCE Line
Whitepaper Library
Calendar of Events
Association Locator
Contents Pages
Market Research
Subscription Center


 

   
issue: October 2003 APPLIANCE Magazine Part 2: Motors & Air-Moving Devices

Motors & Air-Moving Devices
Discovering the Use of Tangential Blowers in Low-Noise Applications


 Printable format
 Email this Article
 Search

Tangential blowers have often been overlooked because of their perceived low efficiency in certain applications and the misunderstanding of their proper use. However, they can be a solution to efficiently move air.

Tangential wheels generally find their best use in low-static applications (generally less than 0.5 in of static pressure), in applications where low noise is critical, and applications that are best filled by a uniform airflow over a wide path or air curtain. The many applications of tangential wheels include refrigeration systems where the wide, narrow band of air is most efficiently used to spread throughout an area; air purifiers where it is desirable to have a maximum surface of air pushing though a filter; and where any wide area needs to be cooled, heated, or have air flowing through it.


Figure 1. Airflow pattern of a tangential blower. (Courtesy of Whirlpool)

Tangential wheels are usually more efficient when a focused flow of air is required to cool or heat an immediate space. When used in this manner, the air does not have to travel long distances, but instead is used in the immediate surroundings such as in wood stoves and gas fireplaces.

One of the reasons that tangential wheels are quieter in comparison to a centrifugal-style blower is that for products with the same cfm rating, the air speed of the tangential wheel is much slower since the outlet area is much larger than that of a centrifugal blower. This can be seen as an advantage because the large area of discharge of the tangential blower does not require additional diffusion, which would create losses and, thus, decrease efficiency.

When compared to double inlet wheels used in a double blower, tangentials will generally provide an equal or slightly increased cfm with the same motor.

Getting the Most Out of a Tangential Blower

As seen in Figure 1, the airflow is tangentially in across the inlet area and tangentially out across the discharge area. The most efficient configuration is when this 90-degree change in direction can be utilized in the design of a product.

Ideally, if filters or coils are involved, tangential blowers should be used in a pull-through rather than a push-through manner. The inlet air speed is over a larger surface and, therefore, is lower than the discharge airspeed. This usually contributes to lowering the static in the system as well.


Figure 2. CLICK for larger graphic.

As discussed, tangential wheels prosper in low-static situations, so it would be a good idea to try to minimize the static in a system to best utilize the power of a blower. This can be achieved by minimizing the changes in direction of airflow within the application and using the 90-degree change within the tangential to its best by positioning the blower where the airflow is required to make a 90-degree turn. Also, funneling of the discharge must be avoided; it is better to reduce the discharge closest to the wheel than to slowly reduce the discharge area, as shown in Figure 2.


Figure 3. CLICK for larger graphic.

Housing design is critical in blower performance (see Figure 3). Some tips include:

  • For optimum cfm, A=0.60F, B=0.85F, C=0.60F, E=F=0.07F, G=15 degrees, and HIJ should be a straight line. If a smaller outlet is necessary, it is better to reduce A first to a minimum of 0.45F, then A and B together rather than funneling the outlet. Air will discharge following the 15 degree upward. If this is not desirable, for maximum discharge, the entire housing must be rotated - G should not be reduced.
  • Reducing A will affect cfm, but not air speed.
  • For noise control, dimensions E and F are critical, with F being the most critical. Reducing both E and F will increase cfm and noise level.
  • When using grills at discharge, the cfm will be directly reduced by the percent of area covered if the blower maintains the same wheel speed.
  • For applications where the motor is running below its maximum speed: when static of any kind is applied to the system at the discharge, the wheel will speed up to try and maintain the same cfm up to the maximum speed of the motor. This is a useful design feature that can be used in an application where static might build with time (as dust in a filter). If the initial motor is designed to run below its maximum speed, this leaves room for the motor to speed up and maintain its performance.
  • This information is provided by Lauria Avon, vice president of Technology for Eucania International Inc., a Canadian-based manufacturer of tangential blowers for heat pumps, air curtains, mini split air-conditioners, wood stoves, gas fireplaces, refrigerated food displays, and air purifiers.


  • October 2003 Special Product Supplement
    Motors & Air-Moving Devices
    by Peter Simmons, Assistant Editor

    1 - The Art of Providing Savings
    2 - Electric Motor Testing on the Production Line
    3 - Integrating Brushless D.C. Motors Into Plastic Fans for Efficient, Quiet, and Cost-Effective Appliance Solutions
    4 - Design Platforms
    5 - Discovering the Use of Tangential Blowers in Low-Noise Applications
    6 - Automated and Data-Reliant

    7 - Improving IAQ in the Home
    8 - Floor Care Appliance Boasts 5,000-HR Life
    9 - Getting Pumped Up

     

    Daily News

    ...........................................................

    Aug 29, 2014: Adaptive Frequency Drive Increases Trane Chiller Efficiency

    Aug 29, 2014: Vitamix President Receives Entrepreneur of the Year Award

    Aug 28, 2014: LG Heat Pump Clothes Dryer Earns Emerging Technology Award

    Aug 28, 2014: Early Snowthrower Demand Boosts Toro Sales

    Aug 27, 2014: Sustainability Standard Launched for Household Portable and Floor Care Appliances

    More Daily News>>

    RSS Feeds
    .........................................................
    Appliance Industry
    Market Research

    ...........................................................

    March 2014: Market Research - 62nd Annual U.S. Appliance Industry Forecast
    February 2014: Appliance Magazine Market Insight: December 2013
    January 2014: Market Research - Appliance Historical Statistical Review: 1954-2012
    January 2014: Appliance Magazine Market Insight: November 2013




     
    Contact Us | About Us | Subscriptions | Advertising | Home
    UBM Canon © 2014  

    Please visit these other UBM Canon sites

    UBM Canon Corporate | Design News | Test & Measurement World | Packaging Digest | EDN | Qmed | Pharmalive | Plastics Today | Powder Bulk Solids | Canon Trade Shows